Logan Reid
To turn on the Sunbeam Hospitality Iron, plug it in and wait for it to heat up. The light under the selected fabric setting will turn solid blue when it's ready to use. If the indicator light starts flashing, this may be due to a safety feature that turns the iron off when it hasn't been used for several minutes. To reset the iron, move it back and forth and reheat it until the Ready indicator light turns solid blue.
| Characteristics | Values |
|---|---|
| Resetting | Move the iron back and forth and reheat until the “Ready” indicator light turns solid blue |
| Water type | Tap water can be used unless the water in the area is very hard, which will reduce the iron's performance |
| Water type (continued) | If the water in your area is very hard, use demineralized or distilled water |
| Water tank | It is not necessary to empty the water from the iron after every use |
| Storage | If you do not use your iron frequently, it is recommended to empty the water reservoir, turn the Fabric Select Dial and Steam Lever to O/Off, and allow the iron to cool before putting it away |
| Heating | Allow the iron to reach operating temperature (about 2 minutes) before turning the steam dial to the desired setting |
| Heating (continued) | When turned on for the first time, the iron may give off a slight odor for up to ten minutes due to the initial heating of the materials used |
| Heating (continued) | Place the iron on a stable, protected surface while it is heating |
| Indicator light | A blue light indicates when the iron has reached the appropriate temperature |
| Steam settings | The Steam setting and/or Shot of Steam® feature should only be used with Wool, Cotton, or Linen fabric settings |
| Fabric settings | Press the Fabric Select Button to choose the desired fabric setting |
| Steam lever | When not in use, always set the Steam Lever to "Dry" |
Explore related products
What You'll Learn
Plug in the iron and wait for the indicator light to turn solid blue
To turn on the Sunbeam Hospitality Iron, begin by plugging the iron into a power outlet. The indicator light will start flashing, and the iron will begin to heat up. Place the iron on a stable, protected surface while it heats up. Depending on the model, you may also need to adjust the steam lever to your preferred setting and select the desired fabric setting. If you do not use your iron frequently, it is recommended that you empty the water reservoir and turn the Fabric Select Dial and Steam Lever to "Off" before storing it. Allow the iron to heat up for about two minutes.
Once the iron has reached the appropriate temperature, the indicator light will turn solid blue. This indicates that the iron is ready to use. If the indicator light does not turn solid blue, the steam valve may be set to "dry," or it may be clogged. Move the steam dial back and forth a couple of times to clean the valve and ensure it is on a "steam" setting. Additionally, when you turn on the iron for the first time, it may emit a slight odour due to the initial heating of the materials. This is normal and should dissipate within ten minutes.
If you are using a Sunbeam Turbo Steam Iron, it may also have a three-way motion Smart Auto-off feature. This is a standard safety feature. If your iron has this feature and you need to reset it, simply move the iron back and forth and reheat it until the “Ready” indicator light turns solid blue.
It is important to note that if you do not plan to use the iron for an extended period, you should empty the water reservoir to prevent any potential damage. Additionally, always set the Steam Lever to "Dry" and the Fabric Select Dial to "Off" when the iron is not in use.
Essentials for Your Hospital Stay During Labour
You may want to see also
Explore related products
Use tap water unless you have very hard water, then opt for demineralised or distilled water
When filling up your Sunbeam Hospitality iron with water, it is generally safe to use tap water, unless you have very hard water, in which case you should opt for demineralised or distilled water. Hard water is water that has a high mineral content, specifically calcium and magnesium ions. These ions can build up over time, causing limescale, which can reduce the lifespan of your iron and other appliances.
You may notice that you have hard water if, after washing your hands, they still feel slimy or like there is a film of residue left on them. You may also notice spots or film on your glasses and dishes after washing them, or a lack of foam formation when agitating soap in water. Another indication of hard water is the buildup of limescale in your kettle or water heater.
The hardness of water varies depending on the region, and it is influenced by the presence of certain minerals in the soil and rock that the water passes through. Water with a high concentration of calcium and magnesium ions is considered hard water, while water with few of these ions is considered soft water. Soft water, such as rainwater and distilled water, does not inhibit the lathering action of soaps and does not form soap scum.
If you are unsure about the hardness of your tap water, you can contact your local water supplier or have your water tested. Using demineralised or distilled water in your iron can help prevent the buildup of limescale and extend the lifespan of your appliance. These types of water have had their mineral ions removed and are suitable for use in areas with very hard water.
By following these instructions and being mindful of the water quality in your area, you can ensure that you are using the appropriate type of water in your Sunbeam Hospitality iron and maintain the iron's performance and longevity.
Managing Anxiety Attacks: Valium's Role in Hospital Care
You may want to see also
Explore related products
Adjust the steam lever to your desired setting
Adjusting the steam lever on your Sunbeam Hospitality Iron is a simple process. The steam lever controls the amount of steam that is generated by the iron and can be adjusted to your desired setting.
Firstly, it is important to note that when the iron is not in use, the steam lever should always be set to the 'Dry' or 'Off' position. This is to prevent the steam valve from remaining open, which can cause water to leak from the iron.
To adjust the steam lever, simply move the lever to your desired setting. The Sunbeam iron typically offers settings ranging from 'Off' or 'Dry' to Silk, Wool, Cotton, or Linen. These settings correspond to the type of fabric you are ironing and the amount of steam required. For example, if you are ironing silk, you may want to set the steam lever to a lower setting to avoid damaging the delicate fabric. On the other hand, if you are ironing cotton or linen, you may require more steam to effectively remove wrinkles.
It is important to ensure that the steam setting is appropriate for the fabric type. For instance, if the temperature setting is set to a low temperature, such as for synthetic fabrics, and the steam lever is set to a high steam output, the iron may leak. This is because the temperature is not high enough to generate steam for the selected steam setting.
By adjusting the steam lever, you can control the amount of steam generated by the iron and optimize it for the specific fabric you are working with. This helps to ensure effective ironing while also protecting your fabrics from potential damage caused by excessive steam or heat.
LMU CVM: Teaching Hospital Status and Benefits
You may want to see also
Explore related products
Choose the correct fabric setting
Choosing the correct fabric setting on your iron is crucial to achieving the desired results and avoiding any damage to your garments. Here are some detailed instructions on selecting the right fabric setting for your Sunbeam Hospitality Iron:
Acetate: When ironing acetate fabric, it's important to use a low-temperature setting and avoid using steam. To prevent shine marks, turn the fabric inside out.
Acrylic: For acrylic fabrics, similar to acetate, use a low-temperature setting and avoid steam. Iron the fabric inside out, and ensure it is completely dry to prevent stretching or deformation.
Corduroy: When dealing with corduroy garments, turn them inside out and use a heavy ironing cloth. Smooth the fabric with your hand after ironing to ensure a neat finish.
Cotton: Cotton fabrics should be ironed while they are still damp or pre-moistened with a spray bottle. Set your iron to a high-temperature setting, and use steam to effectively remove stubborn wrinkles and creases.
Cotton-Blend: For cotton-blend fabrics, use a low-heat setting and steam. Ironing the garment inside out or using a press cloth can help prevent iron marks and shine.
Denim: Denim garments require the highest heat setting and steam for effective results. If you want crisp and neatly creased denim, consider using starch.
Linen: To iron linen effectively, turn the garment inside out or use a press cloth to prevent shine. Linen should be ironed while it's still damp or pre-moistened with a spray bottle. For crisp results, use spray-on starch on collars, cuffs, and desired areas.
Nylon: When handling nylon fabric, use the lowest temperature setting and a press cloth to protect the fabric. If needed, you can switch to the "Steamer" function to gently remove wrinkles.
Polyester: For polyester garments, set the iron to low or medium heat, and ensure the fabric is slightly damp or pre-moistened with a spray bottle.
Rayon: Iron rayon fabric on low heat, without steam, and be sure to iron one small area at a time to avoid stretching.
Silk: Silk garments should be ironed while they are still damp or pre-moistened. Use the lowest heat setting and place a press cloth between the iron and the fabric to prevent shine.
Viscose: Similar to silk, viscose should be ironed while damp or pre-moistened. Use the lowest temperature setting with a dry iron, unless the care tag specifies otherwise. A press cloth will help prevent shine.
Wool and Wool-Blends: Wool and wool-blend fabrics should be ironed on low heat with steam. Avoid ironing wool when it's dry to prevent fabric damage.
Remember, always check the garment's care label and follow the manufacturer's instructions. If no instructions are provided, start with a low-heat setting and gradually increase the temperature.
Hospitals: Treating Physicians and Employees Differently
You may want to see also
Explore related products
Reset the iron by moving it back and forth and reheating
To reset the Sunbeam Hospitality Iron, a simple procedure is required. Begin by unplugging the iron from the power source. This step is crucial as it ensures that the iron is completely disconnected from any power supply, allowing for a safe reset process. Wait for at least 30 seconds after unplugging. During this time, the iron's internal components will be without power, and any residual electricity will dissipate. Now, move the iron back and forth a few times while it is still unplugged. This physical action serves to reset the mechanism and prepare it for the next step.
The next step is to plug the iron back into the power source. This re-establishes the electrical connection, providing power to the iron so it can heat up again. After plugging it in, allow the iron to heat up for a few minutes. This gives time for the internal components to reach the optimal temperature and for the iron to recover its full functionality. During this period, you may notice indicator lights or hear sounds signaling that the iron is heating up, depending on your model.
Once the iron has had sufficient time to heat up, you can confirm that the reset was successful by checking for heat on the soleplate. Carefully touch the soleplate to feel if it has reached the desired temperature. If the iron has successfully reset, the soleplate should be hot and ready for use. If, for any reason, the iron does not heat up as expected, you may need to repeat the reset process or refer to the iron's user manual for additional troubleshooting tips specific to your model.
It is important to remember that the reset process is typically effective in resolving minor issues with the iron's performance. However, if you encounter persistent problems or the iron is not functioning properly, it is always best to consult the user manual or seek assistance from the manufacturer or a qualified technician. They can provide model-specific advice and ensure that you can use your Sunbeam Hospitality Iron safely and effectively.
Griffin Hospital: Certified Primary Stroke Center
You may want to see also
